CMD_PROP_TX_ADV/CMD_PROP_RX_ADV

最近在使用SmartRF Studio对CC1310 B版本进行smartrf-settings.c的配置，

需要配置出625bps长距离模式的CMD_PROP_TX_ADV/CMD_PROP_RX_ADV命令参数，

然而SmartRF studio只能配置出CMD_PROP_TX/CMD_PROP_RX的参数，而不能配置出

CMD_PROP_TX_ADV/CMD_PROP_RX_ADV命令参数，那怎么能够配置出高级模式的

CMD_PROP_TX_ADV/CMD_PROP_RX_ADV命令参数？

在code export窗口中，按如下步骤操作即可。

这个我早试过了，移植到contikI的驱动下不能够工作。主要的原因是SmartRF只针对CMD_PROP_TX 和CMD_PROP_RX命令，对于

CMD_PROP_TX_ADV 和CMD_PROP_RX_ADV命令不能够配置出相应的参数，比如变化CMD_PROP_TX的参数，CMD_PROP_TX_ADV

参数不会跟着变化。具体原因我参考是https://e2e.ti.com/support/wireless_connectivity/proprietary_sub_1_ghz_simpliciti/f/156/t/479285?tisearch=e2e-sitesearch&keymatch=CC1310%20CMD_PROP_TX_ADV

目前我采用的配置如下，CC1310-A版本的长距离模式（625bps）能够在contiki上运行。

/*---------------------------------------------------------------------------*/
/* Overrides for CMD_PROP_RADIO_div_SETUP */
static uint32_t overrides[] =
{
  // override_use_patch_prop_lrm.xml
    // PHY: Use MCE ROM bank 3, RFE RAM patch
    MCE_RFE_OVERRIDE(0,3,0,1,0,0),
    // override_synth_prop_430_510_div10.xml
    // Synth: Set recommended RTRIM to 7
    HW_REG_OVERRIDE(0x4038,0x0037),
    // Synth: Set Fref to 4 MHz
    (uint32_t)0x000684A3,
    // Synth: Configure fine calibration setting
    HW_REG_OVERRIDE(0x4020,0x7F00),
    // Synth: Configure fine calibration setting
    HW_REG_OVERRIDE(0x4064,0x0040),
    // Synth: Configure fine calibration setting
    (uint32_t)0xB1070503,
    // Synth: Configure fine calibration setting
    (uint32_t)0x05330523,
    // Synth: Set loop bandwidth after lock to 20 kHz
    (uint32_t)0x0A480583,
    // Synth: Set loop bandwidth after lock to 20 kHz
    (uint32_t)0x7AB80603,
    // Synth: Configure VCO LDO (in ADI1, set VCOLDOCFG=0x9F to use voltage input reference)
    ADI_REG_OVERRIDE(1,4,0x9F),
    // Synth: Configure synth LDO (in ADI1, set SLDOCTL0.COMP_CAP=1)
    ADI_HALFREG_OVERRIDE(1,7,0x4,0x4),
    // Synth: Use 24 MHz XOSC as synth clock, enable extra PLL filtering
    (uint32_t)0x02010403,
    // Synth: Configure extra PLL filtering
    (uint32_t)0x00108463,
    // Synth: Increase synth programming timeout (0x04B0 RAT ticks = 300 us)
    (uint32_t)0x04B00243,
    // override_phy_rx_aaf_bw_0xd.xml
    // Rx: Set anti-aliasing filter bandwidth to 0xD (in ADI0, set IFAMPCTL3[7:4]=0xD)
    ADI_HALFREG_OVERRIDE(0,61,0xF,0xD),
    // override_phy_gfsk_rx.xml
    // Rx: Set LNA bias current trim offset to 3
    (uint32_t)0x00038883,
    // Rx: Freeze RSSI on sync found event
    HW_REG_OVERRIDE(0x6084,0x35F1),
    // override_phy_gfsk_pa_ramp_agc_reflevel_0x1a.xml
    // Tx: Configure PA ramping setting (0x41). Rx: Set AGC reference level to 0x1A.
    HW_REG_OVERRIDE(0x6088,0x411A),
    // Tx: Configure PA ramping setting
    HW_REG_OVERRIDE(0x608C,0x8213),
    // override_phy_lrm_rom_dsss8.xml
    // PHY: Configure DSSS=8
    HW_REG_OVERRIDE(0x505C,0x073C),
    // override_phy_rx_rssi_offset_neg2db.xml
    // Rx: Set RSSI offset to adjust reported RSSI by +5 dB
    (uint32_t)0x00FB88A3,
    // TX power override
    // Tx: Set PA trim to max (in ADI0, set PACTL0=0xF8)
    ADI_REG_OVERRIDE(0,12,0xF8),
    (uint32_t)0xFFFFFFFF,
};
/*---------------------------------------------------------------------------*/
/* CMD_PROP_RADIO_div_SETUP */
rfc_CMD_PROP_RADIO_div_SETUP_t smartrf_settings_cmd_prop_radio_div_setup =
{
  .commandNo = 0x3807,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .startTime = 0x00000000,
    .startTrigger.triggerType = 0x0,
    .startTrigger.bEnaCmd = 0x0,
    .startTrigger.triggerNo = 0x0,
    .startTrigger.pastTrig = 0x0,
    .condition.rule = 0x1,
    .condition.nSkip = 0x0,
    .modulation.modType = 0x0,
    .modulation.deviation = 0x14,
    .symbolRate.preScale = 0xF,
    .symbolRate.rateWord = 0x199A,
    .rxBw = 0x20,
    .preamConf.nPreamBytes = 0x3,// number of PreamBytes
    .preamConf.preamMode = 0x0,
    .formatConf.nSwBits = 0x18,//24-bits Sync word length
    .formatConf.bBitReversal = 0x0,
    .formatConf.bMsbFirst = 0x1,//MSB transmitted first
    .formatConf.fecMode = 0x8,//1000:long range mode
    .formatConf.whitenMode = 0x7,//Dynamically 802.15.4g compatible whitener and 16/32-bit CRC
    .config.frontEndMode = 0x0,
    .config.biasMode = 0x1,//
    .config.analogCfgMode = 0x0,
    .config.bNoFsPowerUp = 0x0,
    .txPower = 0x003F,//set application power
    .pRegOverride = overrides,
    .centerFreq = 0x01B1,//set application centerFreq
    .intFreq = 0x8000,
    .loDivider = 0x0A,
};
/*---------------------------------------------------------------------------*/
/* CMD_FS */
rfc_CMD_FS_t smartrf_settings_cmd_fs =
{
  .commandNo = 0x0803,
  .status = 0x0000,
  .pNextOp = 0,
  .startTime = 0x00000000,
  .startTrigger.triggerType = 0x0,
  .startTrigger.bEnaCmd = 0x0,
  .startTrigger.triggerNo = 0x0,
  .startTrigger.pastTrig = 0x0,
  .condition.rule = 0x1,
  .condition.nSkip = 0x0,
  .frequency = 0x01B1,//
  // .frequency = 868,
  .fractFreq = 0x0000,//set application fractFreq
  .synthConf.bTxMode = 0x0,
  .synthConf.refFreq = 0x0,
  .__dummy0 = 0x00,
  .__dummy1 = 0x00,
  .__dummy2 = 0x00,
  .__dummy3 = 0x0000,
};
/*---------------------------------------------------------------------------*/
/*---------------------------------------------------------------------------*/
/* CMD_PROP_TX_ADV */
rfc_CMD_PROP_TX_ADV_t smartrf_settings_cmd_prop_tx_adv =
{
  .commandNo = 0x3803,
  .status = 0x0000,
  .pNextOp = 0,
  .startTime = 0x00000000,
  .startTrigger.triggerType = 0x0,
  .startTrigger.bEnaCmd = 0x0,
  .startTrigger.triggerNo = 0x0,
  .startTrigger.pastTrig = 0x0,
  .condition.rule = 0x1,
  .condition.nSkip = 0x0,
  .pktConf.bFsOff = 0x0,
  .pktConf.bUseCrc = 0x1,
  .pktConf.bCrcIncSw = 0x0, /* .4g mode */
  .pktConf.bCrcIncHdr = 0x0, /* .4g mode */
  .numHdrBits = 0x10 /* 16: .4g mode */,
  .pktLen = 0x0000,
  .startConf.bExtTxTrig = 0x0,
  .startConf.inputMode = 0x0,
  .startConf.source = 0x0,
  .preTrigger.triggerType = TRIG_REL_START,
  .preTrigger.bEnaCmd = 0x0,
  .preTrigger.triggerNo = 0x0,
  .preTrigger.pastTrig = 0x1,
  .preTime = 0x00000000,
  .syncWord = 0x0055904e,
  .pPkt = 0,
};
/*---------------------------------------------------------------------------*/
/* CMD_PROP_RX_ADV */
rfc_CMD_PROP_RX_ADV_t smartrf_settings_cmd_prop_rx_adv =
{
  .commandNo = 0x3804,
  .status = 0x0000,
  .pNextOp = 0,
  .startTime = 0x00000000,
  .startTrigger.triggerType = 0x0,
  .startTrigger.bEnaCmd = 0x0,
  .startTrigger.triggerNo = 0x0,
  .startTrigger.pastTrig = 0x0,
  .condition.rule = 0x1,
  .condition.nSkip = 0x0,
  .pktConf.bFsOff = 0x0,
  .pktConf.bRepeatOk = 0x1,
  .pktConf.bRepeatNok = 0x1,
  .pktConf.bUseCrc = 0x1,
  .pktConf.bCrcIncSw = 0x0, /* .4g mode */
  .pktConf.bCrcIncHdr = 0x0, /* .4g mode */
  .pktConf.endType = 0x0,
  .pktConf.filterOp = 0x1,
  .rxConf.bAutoFlushIgnored = 0x1,
  .rxConf.bAutoFlushCrcErr = 0x1,
  .rxConf.bIncludeHdr = 0x0,
  .rxConf.bIncludeCrc = 0x0,
  .rxConf.bAppendRssi = 0x1,
  .rxConf.bAppendTimestamp = 0x0,
  .rxConf.bAppendStatus = 0x1,
  .syncWord0 = 0x0055904e,
  .syncWord1 = 0x00000000,
  .maxPktLen = 0x0000, /* To be populated by the driver. */
  .hdrConf.numHdrBits = 0x10, /* 16: .4g mode */
  .hdrConf.lenPos = 0x0, /* .4g mode */
  .hdrConf.numLenBits = 0x0B, /* 11 = 0x0B .4g mode */
  .addrConf.addrType = 0x0,
  .addrConf.addrSize = 0x0,
  .addrConf.addrPos = 0x0,
  .addrConf.numAddr = 0x0,
  .lenOffset = -4, /* .4g mode */
  .endTrigger.triggerType = TRIG_NEVER,
  .endTrigger.bEnaCmd = 0x0,
  .endTrigger.triggerNo = 0x0,
  .endTrigger.pastTrig = 0x0,
  .endTime = 0x00000000,
  .pAddr = 0,
  .pQueue = 0,
  .pOutput = 0,
};