CC1101接收出错问题分析！

各位攻城狮大大，我这里有一个问题困扰了我好几天了，在对CC1101的寄存器进行配置后。我使用了两个模块，一种一个模块用于发送数据，另一个模块用于接收，寄存器配置相同。配置如下：

// Write register settings
TI_CC_SPIWriteReg(TI_CCxxx0_IOCFG2, 0x0B); // GDO2 output pin config.
TI_CC_SPIWriteReg(TI_CCxxx0_IOCFG0, 0x06); // GDO0 output pin config.
TI_CC_SPIWriteReg(TI_CCxxx0_FIFOTHR, 0x01); // RX -- 8 byte

TI_CC_SPIWriteReg(TI_CCxxx0_SYNC1, 0x7A); // SYNC1 High byte
TI_CC_SPIWriteReg(TI_CCxxx0_SYNC0, 0x0E); // SYNC0 low byte

TI_CC_SPIWriteReg(TI_CCxxx0_PKTLEN, 0x08); // Packet length. -------------------
TI_CC_SPIWriteReg(TI_CCxxx0_PKTCTRL1, 0x04); // Packet automation control.---------
TI_CC_SPIWriteReg(TI_CCxxx0_PKTCTRL0, 0x04); // Packet automation control.---------
TI_CC_SPIWriteReg(TI_CCxxx0_ADDR, 0x00); // -- Device address.
TI_CC_SPIWriteReg(TI_CCxxx0_CHANNR, 0x00); // Channel number.

TI_CC_SPIWriteReg(TI_CCxxx0_FSCTRL0, 0x00); // --- add
TI_CC_SPIWriteReg(TI_CCxxx0_FSCTRL1, 0x0B); // Freq synthesizer control.
TI_CC_SPIWriteReg(TI_CCxxx0_FSCTRL0, 0x00); // Freq synthesizer control.
// 433MHz
TI_CC_SPIWriteReg(TI_CCxxx0_FREQ2, 0x10); // Freq control word, high byte
TI_CC_SPIWriteReg(TI_CCxxx0_FREQ1, 0xA7); // Freq control word, mid byte.
TI_CC_SPIWriteReg(TI_CCxxx0_FREQ0, 0x62); // Freq control word, low byte.

TI_CC_SPIWriteReg(TI_CCxxx0_MDMCFG4, 0x5B); // Modem configuration.
TI_CC_SPIWriteReg(TI_CCxxx0_MDMCFG3, 0xF8); // Modem configuration.
TI_CC_SPIWriteReg(TI_CCxxx0_MDMCFG2, 0x03); // Modem configuration.
// 0x73 -- 2
TI_CC_SPIWriteReg(TI_CCxxx0_MDMCFG1, 0x22); // Modem configuration.
TI_CC_SPIWriteReg(TI_CCxxx0_MDMCFG0, 0xF8); // Modem configuration.

TI_CC_SPIWriteReg(TI_CCxxx0_DEVIATN, 0x47); // Modem dev (when FSK mod en)
TI_CC_SPIWriteReg(TI_CCxxx0_MCSM1 , 0x30); // MainRadio Cntrl State Machine
TI_CC_SPIWriteReg(TI_CCxxx0_MCSM0 , 0x18); // MainRadio Cntrl State Machine

TI_CC_SPIWriteReg(TI_CCxxx0_FOCCFG, 0x1D); // Freq Offset Compens. Config
TI_CC_SPIWriteReg(TI_CCxxx0_BSCFG, 0x1C); // Bit synchronization config.

TI_CC_SPIWriteReg(TI_CCxxx0_AGCCTRL2, 0xC7); // AGC control.
TI_CC_SPIWriteReg(TI_CCxxx0_AGCCTRL1, 0x00); // AGC control.
TI_CC_SPIWriteReg(TI_CCxxx0_AGCCTRL0, 0xB2); // AGC control.

TI_CC_SPIWriteReg(TI_CCxxx0_FREND1, 0xB6); // Front end RX configuration.
TI_CC_SPIWriteReg(TI_CCxxx0_FREND0, 0x10); // Front end RX configuration.

TI_CC_SPIWriteReg(TI_CCxxx0_FSCAL3, 0xEA); // Frequency synthesizer cal.
TI_CC_SPIWriteReg(TI_CCxxx0_FSCAL2, 0x2A); // Frequency synthesizer cal.
TI_CC_SPIWriteReg(TI_CCxxx0_FSCAL1, 0x00); // Frequency synthesizer cal.
TI_CC_SPIWriteReg(TI_CCxxx0_FSCAL0, 0x11); // Frequency synthesizer cal.

TI_CC_SPIWriteReg(TI_CCxxx0_FSTEST, 0x59); // Frequency synthesizer cal.
TI_CC_SPIWriteReg(TI_CCxxx0_TEST2, 0x88); // Various test settings.
TI_CC_SPIWriteReg(TI_CCxxx0_TEST1, 0x31); // Various test settings.
TI_CC_SPIWriteReg(TI_CCxxx0_TEST0, 0x09); // Various test settings.

但是，出现了一个问题，就是在接收端的数据不对，并且不能通过CRC校验。接收到的数据如下：（请各位大侠出手相助）

在线等，请各位给个思路。

HI

请用SmartRF Studio 7 配置