CC1310 AD采集和定时器问题

刚接触CC1310，很多问题不明白，望解答。

1、CC1310的AD采集频率最小可以设为多少呢，是不是1s？如果想设为分钟级别的采集，该如何实现，使用Timer还是RTC实现？

2、定时器Timer的最大定时可以是多少呢？TimerConfigure(GPT0_BASE, TIMER_CFG_SPLIT_PAIR | TIMER_CFG_A_PERIODIC | TIMER_CFG_B_PERIODIC);这句中TIMER_CFG_SPLIT_PAIR | TIMER_CFG_A_PERIODIC | TIMER_CFG_B_PERIODIC是什么意思呢？

修改TimerLoadSet(GPT0_BASE, TIMER_A, 1); 中的初值对定时时间没有影响，为什么呢？

希望TI工程师能帮忙解答，谢谢。

CC1310的AD的最大采样频率是200k，小于等于这个频率的都是可以实现的。

关于TimerConfigure()中参数的含义，可在timer.h中看到，如下所示。

//*****************************************************************************
//
//! \brief Configures the timer(s).
//!
//! This function configures the operating mode of the timer(s). The timer
//! module is disabled before being configured and is left in the disabled
//! state.
//!
//! The timers are comprised of two 16-bit timers that can
//! operate independently or be concatenated to form a 32-bit timer.
//!
//! \note If the timers are used independently the length of timer can be
//! extended to 24 bit by use of an 8 bit prescale register set using
//! \ref TimerPrescaleSet().
//!
//! When configuring for full-width timer \c ui32Config is set
//! as one of the following values:
//! - \ref TIMER_CFG_ONE_SHOT : Full-width one-shot timer.
//! - \ref TIMER_CFG_ONE_SHOT_UP : Full-width one-shot timer that counts up
//! instead of down.
//! - \ref TIMER_CFG_PERIODIC : Full-width periodic timer.
//! - \ref TIMER_CFG_PERIODIC_UP : Full-width periodic timer that counts up
//! instead of down.
//!
//! When configuring for a pair of half-width timers, each timer is separately
//! configured. The timers are configured by setting \c ui32Config to
//! the bitwise OR of one of each of the following three:
//! - Use half-width timers:
//! - \ref TIMER_CFG_SPLIT_PAIR
//! - Timer A:
//! - \ref TIMER_CFG_A_ONE_SHOT : Half-width one-shot timer
//! - \ref TIMER_CFG_A_ONE_SHOT_UP : Half-width one-shot timer that counts up
//! instead of down.
//! - \ref TIMER_CFG_A_PERIODIC : Half-width periodic timer
//! - \ref TIMER_CFG_A_PERIODIC_UP : Half-width periodic timer that counts up
//! instead of down.
//! - \ref TIMER_CFG_A_CAP_COUNT : Half-width edge count capture
//! - \ref TIMER_CFG_A_CAP_COUNT_UP : Half-width edge count capture that counts
//! up instead of down.
//! - \ref TIMER_CFG_A_CAP_TIME : Half-width edge time capture
//! - \ref TIMER_CFG_A_CAP_TIME_UP : Half-width edge time capture that counts up
//! instead of down.
//! - \ref TIMER_CFG_A_PWM : Half-width PWM output
//! - Timer B:
//! - Same as Timer A but using TIMER_CFG_B_* instead.
//!
//! \param ui32Base is the base address of the timer module.
//! \param ui32Config is the configuration for the timer.
//!
//! \return None
//
//*****************************************************************************
extern void TimerConfigure(uint32_t ui32Base, uint32_t ui32Config);

您好，感谢您的回复。我问的是最小的采集频率，我想实现的是几分钟采集一次？adcBuf采集例程中adcBufParams.samplingFrequency 最小只能是1吧？分钟级别的采集该如何设置？

将adcBufParams.samplingFrequency设置为1，是ADCBuf_RECURRENCE_MODE_CONTINUOUS模式下最小采样频率，即最大采样间隔。

如果需要采样间隔更大，可以参照adcsinglechannel示例，在你希望进行采样的时间点，通过调用ADC_convert()触发一次采样。

您好，感谢您的回复。我先试试，那我应该怎样延时呢？用Timer还是RTC呢？Timer的最大定时时间是多少呢？

你可以使用Clock module，默认时间精度是10us，定时时长为32位无符号整形数。