基于STM32和DS1302设计的时钟程序

me[3]/16*10+settime[3]%16;

d[4]=settime[4]/16*10+settime[4]%16;

d[5]=settime[5]/16*10+settime[5]%16;

d[6]=settime[6]/16*10+settime[6]%16;

//d_convert();

}

应用举例

main.c

#include "stm32f10x.h"

#include"1602.h"

#include"ds1302.h"

EXTI_InitTypeDef EXTI_InitStructure;

ErrorStatus HSEStartUpStatus;

/* Private function prototypes -----------------------------------------------*/

void RCC_Configuration(void);

void GPIO_Configuration(void);

void NVIC_Configuration(void);

u8 table[]="2010-4-30";

u8 table1[3]="hjw";

u8 table2[2]="00";

void Delay(unsigned short time)//nms

{

unsigned short i, j;

for(; time > 0; time--){

for(j = 0; j 10; j++){

for(i = 0; i 1000; i++);

}

}

}

int main(void)

{

//u8 i;

/* System Clocks Configuration */

RCC_Configuration();

/* NVIC configuration */

NVIC_Configuration();

/* Configure the GPIO ports */

GPIO_Configuration();

lcd1602_init();

ds1302set_time();

while (1)

{

ds1302read_time();

ds1302d_convert();

write1602_Achar(1,2,disp[8]);

write1602_Achar(1,3,disp[9]); //显示 时

write1602_Achar(1,4,0x0a);//':'

write1602_Achar(1,5,disp[10]);

write1602_Achar(1,6,disp[11]);

write1602_Achar(1,7,0x0a);//显示分

write1602_Achar(1,8,disp[12]);

write1602_Achar(1,9,disp[13]);//显示秒

}

}

void RCC_Configuration(void)

{

RCC_DeInit();

/* Enable HSE */

RCC_HSEConfig(RCC_HSE_ON);

/* Wait till HSE is ready */

HSEStartUpStatus = RCC_WaitForHSEStartUp();

if(HSEStartUpStatus == SUCCESS)

{

/* Enable Prefetch Buffer */

FLASH_PrefetchBufferCmd(FLASH_PrefetchBuffer_Enable);

/* Flash 2 wait state */

FLASH_SetLatency(FLASH_Latency_2);

/* HCLK = SYSCLK */

RCC_HCLKConfig(RCC_SYSCLK_Div1);

/* PCLK2 = HCLK */

RCC_PCLK2Config(RCC_HCLK_Div1);

/* PCLK1 = HCLK/2 */

RCC_PCLK1Config(RCC_HCLK_Div2);

/* PLLCLK = 8MHz * 9 = 72 MHz */

RCC_PLLConfig(RCC_PLLSource_HSE_Div1, RCC_PLLMul_9);

/* Enable PLL */

RCC_PLLCmd(ENABLE);

/* Wait till PLL is ready */

while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET)

{

}

/* Select PLL as system clock source */

RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);

/* Wait till PLL is used as system clock source */

while(RCC_GetSYSCLKSource() != 0x08)

{

}

}

/* Enable Key Button GPIO Port, GPIO_LED and AFIO clock */

RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC|RCC_APB2Periph_GPIOA| RCC_APB2Periph_GPIOD | RCC_APB2Periph_GPIOB

| RCC_APB2Periph_AFIO, ENABLE);

}

/*******************************************

* Function Name : GPIO_Configuration

* Description : Configures the different GPIO ports.

* Input : None

* Output : None

* Return : None

***************************************/

void GPIO_Configuration(void)

{

GPIO_InitTypeDef GPIO_InitStructure;

GPIO_InitStructure.GPIO_Pin =GPIO_Pin_All;

GPIO_InitStructure.GPIO_Speed =GPIO_Speed_50MHz;

GPIO_InitStructure.GPIO_Mode =GPIO_Mode_Out_PP;

GPIO_Init(GPIOB, GPIO_InitStructure);

}

void NVIC_Configuration(void)

{

//NVIC_InitTypeDef NVIC_InitStructure;

#ifdef VECT_TAB_RAM

/* Set the Vector Table base location at 0x20000000 */

NVIC_SetVectorTable(NVIC_VectTab_RAM, 0x0);

#else /* VECT_TAB_FLASH */

/* Set the Vector Table base location at 0x08000000 */

NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x0);

#endif

}