mt6735 Bluetooth Test
时间：10-02
整理：3721RD
点击：
[DESCRIPTION]
bluetooth Test
(此測項需準備另外一台機器B做交互測試，不限定手機, 需確認android version & APK version是同一版即可)
[Test Steps]
1. Toggle Bluetooth
Enable Bluetooth -> Yes -> Disable Bluetooth -> Enable Bluetooth -> Yes, 可正常開關則選Pass，若不正常，則選Fail.
先將BT打開再進行下面測試
2. BLE CLIent Test (機器A) 與機器B(選擇BLE Server Test)做交互測試~ 請務必依照下列
1.2.3.6.4.5.7.8.的測試順序
1) BLE Client Connect: 輸入機器B的BT address (Settings/About phone/Status/Bluetooth
address) -> 機器A.B出現確認Pair的畫面(也可能會出現在status bar) -> 兩邊都點選”Pair” -> PASS
2) BLE Discover Service: 點下”Discover service” -> 出現”Service discovered” -> PASS
3) BLE Read/Write Characteristic: 輸入“test” -> 點下“Write” -> 出現”Write successful callback” -> 點下“Read”, 顯示”test”-> PASS
6) BLE Read/Write Descriptor: 輸入“test” -> 點下“Write” -> 出現”Write successful callback” -> 點下“Read”, 顯示”test” -> PASS
4) BLE Reliable Write:輸入機器B的BT device name -> 依序點下“Begin write” , “Write”& “Execute write” -> 出現“Write value verified” -> PASS (4.4_r1.95, PASS icon無法點選 -> Google known issue)
5) BLE Notify Characteristic: 點下“Begin notification” -> 出現時間以秒計時 -> PASS
7) BLE Read RSSI: 點下“Read RSSI -> 將兩台機器的距離拉遠, 負數值會越大; 反之, 越靠近,其負數值越小 -> 觀察RSSI的數字變化 -> PASS
8) BLE Client Disconnect: 點下“Disconnect” -> 顯示“Bluetooth LE disconnected” ->PASS
3. BLE Server Test
將機器A跟機器B角色對調後, 同上述測試步驟.
(此測項需準備另外一台機器B做交互測試，不限定手機或平板, 只需確認android version & APK
version 是同一版即可)
4. Insecure Client
機器A（有執行過前面測項的機器）開啟『Insecure Client』-> Yes。
機器B 安裝CTSVerifier.apk並執行CTS Verifier。
機器B 開啟『Insecure Server』 -> Yes -> OK -> 點選下方『Make Discoverable』。
機器A -> 點選Scan for Devices（多按幾次確認上方字樣為Scanning） -> 在New Devices清單點
選機器B進行連結（配對需在機器B於Make Discoverable點選後30秒內完成，否則無法連結成功。）
檢查Sent Messages下方的『Message＊ to 機器B』 是否全部顯示在機器B的Received Messages內
容中 >有則Pass，無則Fail。
5. Insecure Server
機器A -> 執行『Insecure Server』，機器B執行『Insecure Client』，測試步驟如 2. Insecure
Client，兩台device角色對調。
6. Secure Client
機器A 點選『Secure Client』，機器B點選『Secure Server』-> OK -> Make Discoverable >
Yes。
機器A -> Scan for Devices -> 找到機器B進行配對 -> Pair -> 機器B -> Pair（機器AB皆須按Pai若清單無設備，則此測項Fail。
配對需在機器B於Make Discoverable點選後30秒內完成，否則無 法配對成功。）
檢查Sent Messages下方的『Message ＊ to 機器B』 是否全部顯示在機器B的Received Messages內容中 >有則Pass，無則Fail。
7. Secure Server
機器A -> 執行『Secure Server』，機器B執行『Secure Client』，測試步驟如 4. Secure
Client，兩台device角色對調。
若Bluetooth的七個測項皆為Pass，則點選下方Pass，若有一項以上的測項為Fail，則點選Fail。
bluetooth Test
(此測項需準備另外一台機器B做交互測試，不限定手機, 需確認android version & APK version是同一版即可)
[Test Steps]
1. Toggle Bluetooth
Enable Bluetooth -> Yes -> Disable Bluetooth -> Enable Bluetooth -> Yes, 可正常開關則選Pass，若不正常，則選Fail.
先將BT打開再進行下面測試
2. BLE CLIent Test (機器A) 與機器B(選擇BLE Server Test)做交互測試~ 請務必依照下列
1.2.3.6.4.5.7.8.的測試順序
1) BLE Client Connect: 輸入機器B的BT address (Settings/About phone/Status/Bluetooth
address) -> 機器A.B出現確認Pair的畫面(也可能會出現在status bar) -> 兩邊都點選”Pair” -> PASS
2) BLE Discover Service: 點下”Discover service” -> 出現”Service discovered” -> PASS
3) BLE Read/Write Characteristic: 輸入“test” -> 點下“Write” -> 出現”Write successful callback” -> 點下“Read”, 顯示”test”-> PASS
6) BLE Read/Write Descriptor: 輸入“test” -> 點下“Write” -> 出現”Write successful callback” -> 點下“Read”, 顯示”test” -> PASS
4) BLE Reliable Write:輸入機器B的BT device name -> 依序點下“Begin write” , “Write”& “Execute write” -> 出現“Write value verified” -> PASS (4.4_r1.95, PASS icon無法點選 -> Google known issue)
5) BLE Notify Characteristic: 點下“Begin notification” -> 出現時間以秒計時 -> PASS
7) BLE Read RSSI: 點下“Read RSSI -> 將兩台機器的距離拉遠, 負數值會越大; 反之, 越靠近,其負數值越小 -> 觀察RSSI的數字變化 -> PASS
8) BLE Client Disconnect: 點下“Disconnect” -> 顯示“Bluetooth LE disconnected” ->PASS
3. BLE Server Test
將機器A跟機器B角色對調後, 同上述測試步驟.
(此測項需準備另外一台機器B做交互測試，不限定手機或平板, 只需確認android version & APK
version 是同一版即可)
4. Insecure Client
機器A（有執行過前面測項的機器）開啟『Insecure Client』-> Yes。
機器B 安裝CTSVerifier.apk並執行CTS Verifier。
機器B 開啟『Insecure Server』 -> Yes -> OK -> 點選下方『Make Discoverable』。
機器A -> 點選Scan for Devices（多按幾次確認上方字樣為Scanning） -> 在New Devices清單點
選機器B進行連結（配對需在機器B於Make Discoverable點選後30秒內完成，否則無法連結成功。）
檢查Sent Messages下方的『Message＊ to 機器B』 是否全部顯示在機器B的Received Messages內
容中 >有則Pass，無則Fail。
5. Insecure Server
機器A -> 執行『Insecure Server』，機器B執行『Insecure Client』，測試步驟如 2. Insecure
Client，兩台device角色對調。
6. Secure Client
機器A 點選『Secure Client』，機器B點選『Secure Server』-> OK -> Make Discoverable >
Yes。
機器A -> Scan for Devices -> 找到機器B進行配對 -> Pair -> 機器B -> Pair（機器AB皆須按Pai若清單無設備，則此測項Fail。
配對需在機器B於Make Discoverable點選後30秒內完成，否則無 法配對成功。）
檢查Sent Messages下方的『Message ＊ to 機器B』 是否全部顯示在機器B的Received Messages內容中 >有則Pass，無則Fail。
7. Secure Server
機器A -> 執行『Secure Server』，機器B執行『Secure Client』，測試步驟如 4. Secure
Client，兩台device角色對調。
若Bluetooth的七個測項皆為Pass，則點選下方Pass，若有一項以上的測項為Fail，則點選Fail。