出Error: Connect failed, Exit Meta Mode and turn to next phone.的请进

线刷机时因为手贱，点了FORMAT后，结果就出8038错误，后来弄到半夜终于刷成功了，但MAC和IMEI已经丢失。用了几天后发现并不太影响使用，但看着很不爽。研究了半个多月，电脑重装N次，两台电脑来回折腾终于把MAC和IMEI恢复了。具体教程可以开GOOGLE搜索“恢复IMEI” 网上恢复MAC和IMEI的教程很多，但我照他们的方法做不成功，具体就是在插入USB线后提示Error: Connect failed, Exit Meta Mode anDTUrn to next phone. 之前的信息是：>>Step: Start to Connect with target.COM port searching and preloader handshakeCOM port searching and preloader handshakeokCOM port searching and Kernel handshake   Error: Connect failed, Exit Meta Mode and turn to next phone. 开始以为是驱动不对，弄了很久，也没结果。经过半个月的折腾终于弄清楚，Modem Database和AP Database文件必须从原版相同版本的线刷包中提取，否则会出错。 例如，我的机现在的ROM版本为S510_131122,那么，这个软件中的所选的MODEM Database和AP Database文件就必须从S510_131122版本的刷机包中提取，不能用别的文件！   现阶段网上所有的教程，没有一个提到版本问题，最多就是提供这两个文件的下载连接。 卡刷包本人没有试过，为了保险还是先刷原厂线刷包，完了再用这个线刷包里的MODEM Database和AP Database文件。  下面是刷机正常时的提示信息：(1)IMEI部分>>Step: Enterfunc_imei_meta_hdlr_smart_phone_modem();        Write IMEI to smartphone modem nvram>>Step: Start to Init Modem NvramDatabase...  OK: Init Modem Nvram Database successfully. >>---------------------------------------------------<<   OK: IMEI[0] = "8600XXXXXXXXXXX".  >>Step: Start to Connect with target.COM port searching and preloader handshakeCOM port searching and preloader handshakeokCOM port searching and Kernel handshake  OK: Connect successfully.>>Step: To get SVN and PAD fromphone.  OK: SVN=0xff and PAD=0xff >>Step: Start to write. CheckSum=1,IMEILock=0.  OK: Write IMEI successfully.  OK: Check IMEI. Rd_imei = "8600XXXXXXXXXXX".   OK: IMEI[1] = "8600XXXXXXXXXXX".>>Step: To get SVN and PAD fromphone.  OK: SVN=0xff and PAD=0xff >>Step: Start to write. CheckSum=1, IMEILock=0.  OK: Write IMEI successfully.  OK: Check IMEI. Rd_imei = "8600XXXXXXXXXXX".>> Step: To switch Meta to AP side...   OK: META_DisconnectInMe**ode_r()    OK: Switch2WM_META_Mode() >>Step: To Backup NVRAM to BinRegion, and Set Clean Boot Flag   OK: Backup NVRAM and WM_META_SetCleanBootFlag_Customize() >> Step: Meta Disconnect with target. >>---------------------------------------------------<<>>Step: Cancel scan IMEI DiagBox.  （2）MAC部分 >> Step: To switch Meta to AP side...   OK: META_DisconnectInMe**ode_r()    OK: Switch2WM_META_Mode()  >>Step: To Backup NVRAM to BinRegion, and Set Clean Boot Flag   OK: Backup NVRAM and WM_META_SetCleanBootFlag_Customize()  >> Step: Meta Disconnect with target. >>---------------------------------------------------<<>>Step: Cancel scan IMEI DiagBox.>>-------------------------------------------------------------------<<>>Step: Enterfunc_wifi_mac_meta_hdlr_smart_phone_Ex();       Write wifi MAC  to smart phone nvram>>Step: Start to Init smart phoneDatabase...  OK: Init AP Nvram Database successfully.  >>-------------------------------------------------------------<<>>Step: Scan Smart Phone Wifi MAC.   OK: Wifi MAC = "XXXXXXXXXXX".>>Step: Start to Connect with target.COM port searching and preloader handshakeCOM port searching and preloader handshakeokCOM port searching and Kernel handshakeCOM port searching and Kernel handshake OK   OK: Connect to target successfully.>>Step: Start to write Wifi MAC.   OK: Write Wifi MACsuccessfully.>>Step: Start to check Wifi MAC.   OK: Check Wifi MAC Pass. Wifi MAC = "xxxxxxxxxxxx". >>Step: To Backup NVRAM to BinRegion, and Set Clean Boot Flag   OK: Backup NVRAM and WM_META_SetCleanBootFlag_Customize() >>Step: Meta Disconnect with target. >>-------------------------------------------------------------<<>>Step: Scan Smart Phone Wifi MAC.>>Step: Cancel scan Address DiagBox.    下面是本人不成功时的提示信息：>>Step: Start to Connect with target.COM port searching and preloader handshakeCOM port searching and preloader handshakeokCOM port searching and Kernel handshake   Error: Connect failed, Exit Meta Mode and turn to next phone.