82KK要按开机键10多秒才能正常开机，求解！(结贴)

LOG如下：
CC〃HhU5%u厬懮?0x6E, value after: 7
[USB]addr: 0x22, value: 0
[USB]addr: 0x22, value after: 2
[USB]addr: 0x68, value: 8
[USB]addr: 0x68, value after: 8
[USB]addr: 0x6A, value: 4
[USB]addr: 0x6A, value after: 4
[USB]addr: 0x11002090 (UART1), value: 0
[USB]addr: 0x11002090 (UART1), value after: 1
wait for frequency meter finish, CLK26CALI = 0x81
mt_pll_post_init: mt_get_cpu_freq = 1040000Khz
wait for frequency meter finish, CLK26CALI = 0x90
mt_pll_post_init: mt_get_bus_freq = 273000Khz
wait for frequency meter finish, CLK26CALI = 0x81
mt_pll_post_init: mt_get_mem_freq = 265078Khz
[PWRAP] pwrap_init_preloader
[PWRAP] pwrap_init
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=0,rdata=800
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=1 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=2 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=3 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=4 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=5 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=6 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=7 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=8,rdata=1001
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=9,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=10,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=11,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=12,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=13,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=14,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=15,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=16,rdata=2003
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=17,rdata=6A97
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=18,rdata=6A97
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=19,rdata=6A97
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=20,rdata=6A97
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=21,rdata=6A97
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=22,rdata=6A97
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=23,rdata=6A97
[PWRAP] _pwrap_init_reg_clock
[PMIC_WRAP]wrap_init pass,the return value=0.
[PMIC6323_init] Preloader Start..................
[pmic6323_init] PMIC CHIP Code = 0X2023
INT_MISC_CON: 0  TOP_RST_MISC: 0
pl pmic powerkey Press
[pmic6323_init] powerKey = 1
[pmic6323_init] is USB in = 0xB004
[pmic6323_init] Reg[0x11A]=0x1B
[pmic6323_init] Done...................
chr force en
[PLFM] Init I2C: OK(0)
[PLFM] Init PWRAP: OK(0)
[PLFM] Init PMIC: OK(0)
[PLFM] chip[CA00]
[BLDR] Build Time: 20141023-170124
PS:按下开机键的时候同时也走了检测电池函数，把检测电池函数去掉即可
platform.c     static boot_reason_t platform_boot_status(void)
#if ！CFG_FPGA_PLATFORM
    /* check power key */
    if (mtk_detect_key(8)  {
        print("%s Power key boot！\n", MOD);
        rtc_mark_bypass_pwrkey();
        return BR_POWER_KEY;
    }
#endif

看看VOLUME/HOME这些按键有没有配对

有没有重启?