92开不了机，LOG如下，各位有碰到的吗？

[PWRAP] pwrap_init_preloader
[PWRAP] pwrap_init
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=0,rdata=2D52
[PWRAP] _pwrap_init_sistrobtay in USB Mode
wait for frequency meter finish, CLK26CALI = 0x81
mt_pll_post_init: mt_get_cpu_freq = 845000Khz
wait for frequency meter finish, CLK26CALI = 0x90
mt_pll_post_init:  
mt_pll_post_init: mt_get_mem_freq = 266347Khz
[PWRAP] pwrap_init_preloader
[PWRAP] pwrap_init
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=0,rdata=2D52
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=1,rdata=5A25
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=2 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=3 rdata=5AA5
[PWRAP] _pwrap_i robe [Read Test] pass,index=5 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=6 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=7 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=8 rdata=5AA5
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=9,rdata=B403
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=10,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=11,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=12,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=13,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=14,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=15,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=16,rdata=B54B
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=17,rdata=6897
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=18,rdata=6A97
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=19,rdata=6A97
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=20,rdata=6A97
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=21,rdata=6A97
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=22,rdata=6A97
[PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=23,rdata=6A97
[PWRAP] _pwrap_init_reg_clock
[PMIC_WRAP]wrap_init pass,the return value=0.
[PMIC_init] Preloader Start..................
[pmic_init] PMIC CHIP Code = 0X2023
pl pmic powerkey Release
[pmic_init] PowerKey = 0
[pmic_init] is USB in = 0xB004
[pmic_init] Reg[0x11A]=0x1B
[I2C-PL] 330: id=1,addr: 6B, transfer error
[I2C-PL] 336: I2C_ACKERR
[I2C-PL] 208: I2C structure:
[I2C-PL] Id=1,Mode=1,St_rs=0,DMA_en=0,Op=3,Poll_en=1,Irq_stat=2
[I2C-PL] Trans_len=1,Trans_num=2,Trans_auxlen=1,Data_size=FFFF,speed=100
[I2C-PL] 211: base address 0x11008000
[I2C-PL] 229: I2C register:
[I2C-PL] SLAVE_ADDR=D6,INTR_MASK=F8,INTR_STAT=3,CONTROL=38,TRANSFER_LEN=101
[I2C-PL] TRANSAC_LEN=2,DELAY_LEN=2,TIMING=1132,START=0,FIFO_STAT=1101
[I2C-PL] IO_CONFIG=3,HS=102,DEBUGSTAT=40,EXT_CONF=8001
[I2C-PL] 820: write_read 0x101 bytes fails,ret=-121.
MT6333_read_byte: i2c_read: ret_code: -1
[mt6333_init] Reg[0]=0x0
[I2C-PL] 330: id=1,addr: 6B, transfer error
[I2C-PL] 336: I2C_ACKERR
[I2C-PL] 208: I2C structure:
[I2C-PL] Id=1,Mode=1,St_rs=0,Dma_en=0,Op=3,Poll_en=1,Irq_stat=2
[I2C-PL] Trans_len=1,Trans_num=2,Trans_auxlen=1,Data_size=FFFF,speed=100
[I2C-PL] 211: base address 0x11008000
[I2C-PL] 229: I2C register:
[I2C-PL] SLAVE_ADDR=D6,INTR_MASK=F8,INTR_STAT=3,CONTROL=38,TRANSFER_LEN=101
[I2C-PL] TRANSAC_LEN=2,DELAY_LEN=2,TIMING=1132,START=0,FIFO_STAT=1101
[I2C-PL] IO_CONFIG=3,HS=102,DEBUGSTAT=40,EXT_CONF=8001
[I2C-PL] 820: write_read 0x101 bytes fails,ret=-121.
mt6333_read_byte: i2c_read: ret_code: -1
[mt6333_init] Reg[FD]=0xFD
[I2C-PL] 330: id=1,addr: 6B, transfer error
[I2C-PL] 336: I2C_ACKERR
[I2C-PL] 208: I2C structure:
[I2C-PL] Id=1,Mode=1,St_rs=0,Dma_en=0,Op=3,Poll_en=1,Irq_stat=2
[I2C-PL] Trans_len=1,Trans_num=2,Trans_auxlen=1,Data_size=FFFF,speed=100
[I2C-PL] 211: base address 0x11008000
[I2C-PL] 229: I2C register:
[I2C-PL] SLAVE_ADDR=D6,INTR_MASK=F8,INTR_STAT=3,CONTROL=38,TRANSFER_LEN=101
[I2C-PL] TRANSAC_LEN=2,DELAY_LEN=2,TIMING=1132,START=0,FIFO_STAT=1101
[I2C-PL] IO_CONFIG=3,HS=102,DEBUGSTAT=40,EXT_CONF=8001
[I2C-PL] 820: write_read 0x101 bytes fails,ret=-121.
mt6333_read_byte: i2c_read: ret_code: -1
[mt6333_init] Reg[2C]=0x2C
[pmic_init] Done...................
[PLFM] Init I2C: OK(0)
[PLFM] Init PWRAP: OK(0)
[PLFM] Init PMIC: OK(0)
[PLFM] chip[CA00]

感觉好像是I2C引起的问题。
注意查一下。

看起来是MT6333 I2C有问题 但别人的板下进去可以开机啊 而且I2C 中断接法一样的 I2C1

看看别人的板，LOG是什么样的。

问题解决了吗? 还请分享下经验。