6572 报错 find no pt or mpt ，哪里需要配置
时间：10-02
整理：3721RD
点击：
C+%?%1u?------ I2C init takes 0 ms --------
[LEDS]LK: leds_init: mt65xx_backlight_off
[LEDS]LK: mt65xx_backlight_off
[LEDS]LK: LCD-backlight level is 0
[LEDS]LK: backlight_set_pwm:duty is 0
[LEDS]LK: backlight_set_pwm:clk_src/div/high/low is 3044
[LEDS]Error level in backlight
[PROFILE] ------- led init takes 3 ms --------
DISP/disp common log enabled
DISP/lcd log enabled
DISP_Init, 623
DISP/DISP_Init, 629
DISP/DISP_Init, 634
DISP/DISP_Init, 640
DISP/DISP_Init, 663
[DISP] - uboot - DSI_powerOn. 0x 0,0x 0,0x 0
div1 should be less than 4！
DISP/[DISP] - kernel - DSI_PHY_TIMCONFIG, Cycle Time = 1231(ns), Unit Interval = 154(ns). div1 = 4, div2 = 2, fbk_div = 0, lane# = 2
DISP/[DISP] - kernel - DSI_PHY_TIMCONFIG, HS_TRAIL = 11, HS_ZERO = 1, HS_PRPR = 1, LPX = 1, TA_GET = 5, TA_SURE = 1, TA_GO = 4, CLK_TRAIL = 10, CLK_ZERO = 0, CLK_HS_PRPR = 1
[DDP]disp_path_config(), srcModule=2, addr=0x0, inFormat=0,
pitch=960, bgROI(0,0,480,800), bgColor=0, outFormat=0, dstModule=19, dstAddr=0x0,
RDMA: w=480, h=800, pitch=1440, mode=0
[DDP] disp_bls_init : srcWidth = 480, srcHeight = 800
DISP/DISP_Init, 668
DISP/DISP_Init, 683
[PROFILE] ------- disp init takes 12 ms --------
[PROFILE] ------- pMIC6329_init takes 0 ms --------
[PROFILE] ------- platform_early_init takes 20 ms --------
[mmc_legacy_init]: start
[mmc_legacy_init]: start mmc_init_host
[SD0] Bus Width: 1
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(0) DDR(0) div(193) DS(0) RS(0)
[mmc_legacy_init]: start mmc_init_card
[mmc_init_card]: start
[SD0] Switch to High-Speed mode！
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(2) DDR(1) div(96) DS(0) RS(0)
[SD0] Bus Width: 8
[SD0] Size: 3728 MB, Max.Speed: 52000 kHz, blklen(512), nblks(7634944), ro(0)
[SD0] Initialized
[SD0] SET_CLK(52000kHz): SCLK(50000kHz) MODE(2) DDR(1) div(0) DS(0) RS(0)
[mmc_init_card]: finish successfully
addr_trans_init
addr_trans_init done
[mt_part_register_device]
[mt_part_register_device]malloc 1024 : 81e55708
MT6577_part_init_pmt
============func=load_pt_fROM_fixed_addr===scan pmt from 700000=====
find no pt or mpt
============func=load_exist_part_tab===scan pmt from 420400=====
[LEDS]LK: leds_init: mt65xx_backlight_off
[LEDS]LK: mt65xx_backlight_off
[LEDS]LK: LCD-backlight level is 0
[LEDS]LK: backlight_set_pwm:duty is 0
[LEDS]LK: backlight_set_pwm:clk_src/div/high/low is 3044
[LEDS]Error level in backlight
[PROFILE] ------- led init takes 3 ms --------
DISP/disp common log enabled
DISP/lcd log enabled
DISP_Init, 623
DISP/DISP_Init, 629
DISP/DISP_Init, 634
DISP/DISP_Init, 640
DISP/DISP_Init, 663
[DISP] - uboot - DSI_powerOn. 0x 0,0x 0,0x 0
div1 should be less than 4！
DISP/[DISP] - kernel - DSI_PHY_TIMCONFIG, Cycle Time = 1231(ns), Unit Interval = 154(ns). div1 = 4, div2 = 2, fbk_div = 0, lane# = 2
DISP/[DISP] - kernel - DSI_PHY_TIMCONFIG, HS_TRAIL = 11, HS_ZERO = 1, HS_PRPR = 1, LPX = 1, TA_GET = 5, TA_SURE = 1, TA_GO = 4, CLK_TRAIL = 10, CLK_ZERO = 0, CLK_HS_PRPR = 1
[DDP]disp_path_config(), srcModule=2, addr=0x0, inFormat=0,
pitch=960, bgROI(0,0,480,800), bgColor=0, outFormat=0, dstModule=19, dstAddr=0x0,
RDMA: w=480, h=800, pitch=1440, mode=0
[DDP] disp_bls_init : srcWidth = 480, srcHeight = 800
DISP/DISP_Init, 668
DISP/DISP_Init, 683
[PROFILE] ------- disp init takes 12 ms --------
[PROFILE] ------- pMIC6329_init takes 0 ms --------
[PROFILE] ------- platform_early_init takes 20 ms --------
[mmc_legacy_init]: start
[mmc_legacy_init]: start mmc_init_host
[SD0] Bus Width: 1
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(0) DDR(0) div(193) DS(0) RS(0)
[mmc_legacy_init]: start mmc_init_card
[mmc_init_card]: start
[SD0] Switch to High-Speed mode！
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(2) DDR(1) div(96) DS(0) RS(0)
[SD0] Bus Width: 8
[SD0] Size: 3728 MB, Max.Speed: 52000 kHz, blklen(512), nblks(7634944), ro(0)
[SD0] Initialized
[SD0] SET_CLK(52000kHz): SCLK(50000kHz) MODE(2) DDR(1) div(0) DS(0) RS(0)
[mmc_init_card]: finish successfully
addr_trans_init
addr_trans_init done
[mt_part_register_device]
[mt_part_register_device]malloc 1024 : 81e55708
MT6577_part_init_pmt
============func=load_pt_fROM_fixed_addr===scan pmt from 700000=====
find no pt or mpt
============func=load_exist_part_tab===scan pmt from 420400=====