单片机——压力传感器LCD

press_bai+0x30);
DisplayOneChar(8,0,press_shi+0x30);
DisplayOneChar(9,0,press_ge +0x30);
DisplayOneChar(11,0,press_dot+0x30);
delay(1000); //稳定显示
}
/************
读ADC0832函数
************/

//采集并返回
uchar Adc0832(unsigned char channel) //AD转换，返回结果
{
uchar i=0;
uchar j;
uint dat=0;
uchar ndat=0;

if(channel==0)channel=2;
if(channel==1)channel=3;
ADDI=1;
_nop_();
_nop_();
ADCS=0;//拉低CS端
_nop_();
_nop_();
ADCLK=1;//拉高CLK端
_nop_();
_nop_();
ADCLK=0;//拉低CLK端,形成下降沿1
_nop_();
_nop_();
ADCLK=1;//拉高CLK端
ADDI=channel&0x1;
_nop_();
_nop_();
ADCLK=0;//拉低CLK端,形成下降沿2
_nop_();
_nop_();
ADCLK=1;//拉高CLK端
ADDI=(channel>>1)&0x1;
_nop_();
_nop_();
ADCLK=0;//拉低CLK端,形成下降沿3
ADDI=1;//控制命令结束
_nop_();
_nop_();
dat=0;
for(i=0;i<8;i++)
{
dat|=ADDO;//收数据
ADCLK=1;
_nop_();
_nop_();
ADCLK=0;//形成一次时钟脉冲
_nop_();
_nop_();
dat<=1;
if(i==7)dat|=ADDO;
}
for(i=0;i<8;i++)
{
j=0;
j=j|ADDO;//收数据
ADCLK=1;
_nop_();
_nop_();
ADCLK=0;//形成一次时钟脉冲
_nop_();
_nop_();
j=j<7;
ndat=ndat|j;
if(i<7)ndat>>=1;
}
ADCS=1;//拉低CS端
ADCLK=0;//拉低CLK端
ADDO=1;//拉高数据端,回到初始状态
dat<=8;
dat|=ndat;
return(dat); //return ad k
}

void data_pro(void)
{
unsigned int temp;
float press;

if(14 {
int vary=ad_data;//y=(115-15)/(243-13)*X+15kpa
press=((10.0/23.0)*vary)+9.3;//测试时补偿值为9.3

temp=(int)(press*10); //放大10倍，便于后面的计算

press_bai=temp/1000; //取压力值百位
press_shi=(temp%1000)/100; //取压力值十位
press_ge=((temp%1000)%100)/10; //取压力值个位
press_dot=((temp%1000)%100)%10;//取压力值十分位

}

}
/*****************报警子函数*******************/
unsigned int a;

void alarm(void)

{
if(ad_data>=243) //如果当前压力值大于115kpa，

{ Alarm_led_red=0;
a=10000;
while(a--);
{
}
Alarm_led_red=1;
a=10000;
while(a--);
{
}
} //则启动red led报警
else
{ Alarm_led_red=1; } //关闭red led 报警

if(ad_data<=14)//如果当前压力值小于16kpa

{ Alarm_led_green=0;
a=10000;
while(a--);
{
}
Alarm_led_green=1;
a=10000;
while(a--);
{
}
} //则启动green led报警

else
{ Alarm_led_green=1; } //关闭green led 报警

}

reg51.h子程序

#ifndef __REG51_H__
#define __REG51_H__

/* BYTE Register */
sfr P0 = 0x80;
sfr P1 = 0x90;
sfr P2 = 0xA0;
sfr P3 = 0xB0;
sfr PSW = 0xD0;
sfr ACC = 0xE0;
sfr B = 0xF0;
sfr SP = 0x81;
sfr DPL = 0x82;
sfr DPH = 0x83;
sfr PCON = 0x87;
sfr TCON = 0x88;
sfr TMOD = 0x89;
sfr TL0 = 0x8A;
sfr TL1 = 0x8B;
sfr TH0 = 0x8C;
sfr TH1 = 0x8D;
sfr IE = 0xA8;
sfr IP = 0xB8;
sfr SCON = 0x98;
sfr SBUF = 0x99;

/* BIT Register */
/* PSW */
sbit CY = 0xD7;
sbit AC = 0xD6;
sbit F0 = 0xD5;
sbit RS1 = 0xD4;
sbit RS0 = 0xD3;
sbit OV = 0xD2;
sbit P = 0xD0;

/* TCON */
sbit TF1 = 0x8F;
sbit TR1 = 0x8E;
sbit TF0 = 0x8D;
sbit TR0 = 0x8C;
sbit IE1 = 0x8B;
sbit IT1 = 0x8A;
sbit IE0 = 0x89;
sbit IT0 = 0x88;

/* IE */
sbit EA = 0xAF;
sbit ES = 0xAC;
sbit ET1 = 0xAB;
sbit EX1 = 0xAA;
sbit ET0 = 0xA9;
sbit EX0 = 0xA8;

/* IP */
sbit PS = 0xBC;
sbit PT1 = 0xBB;
sbit PX1 = 0xBA;
sbit PT0 = 0xB9;
sbit PX0 = 0xB8;

/* P3 */
sbit RD = 0xB7;
sbit WR = 0xB6;
sbit T1 = 0xB5;
sbit T0 = 0xB4;
sbit INT1 = 0xB3;
sbit INT0 = 0xB2;
sbit TXD = 0xB1;
sbit RXD = 0xB0;

/* SCON */
sbit SM0 = 0x9F;
sbit SM1 = 0x9E;
sbit SM2 = 0x9D;
sbit REN = 0x9C;
sbit TB8 = 0x9B;
sbit RB8 = 0x9A;
sbit TI = 0x99;
sbit RI = 0x98;

#endif

INTRINS.H子程序

#ifndef __INTRINS_H__
#define __INTRINS_H__

extern void _nop_ (void);
extern bit _testbit_ (bit);
extern unsigned char _cror_ (unsigned char, unsigned char);
extern unsigned int _iror_ (unsigned int, unsigned char);
extern unsigned long _lror_ (unsigned long, unsigned char);
extern unsigned char _crol_ (unsigned char, unsigned char);
extern unsigned int _irol_ (unsigned int, unsigned char);
extern unsigned long _lrol_ (unsigned long, unsigned char);
extern unsigned char _chkfloat_(float);

#endif

ABSACC.H子程序
#ifndef __ABSACC_H__
#define __ABSACC_H__

#define CBYTE ((unsigned char volatile code *) 0)
#define DBYTE ((unsigned char volatile data *) 0)
#define PBYTE ((unsigned char volatile pdata *) 0)
#define XBYTE ((unsigned char volatile xdata *) 0)