S5PV210启动烧写过程信息

BL_IMAGE_TYPE_BIN

Download BIN file information:
-----------------------------------------------------
[0]: Base Address=0x80020000 Length=0x358c6d0
-----------------------------------------------------
dwStartAddr = 0x80020000
dwLength = 0x358c6d0
NK image
rom_offset=0x0.
ImageStart = 0x80020000, ImageLength = 0x358C6D0, LaunchAddr = 0x80027F34

Completed file(s):
-------------------------------------------------------------------------------
[0]: Address=0x80020000 Length=0x358C6D0 Name="" Target=FLASH
OEMWriteFlash 0x80020000 0x358C6D0
OEMWriteFlash 0x8
Enter LowLevelFormat [0x0, 0x7ff].
Erasing flash block(s) [0x0, 0x7ff] (please wait): EraseBlocks: preserving reserved block (0x0)
EraseBlocks: preserving reserved block (0x1)
EraseBlocks: preserving reserved block (0x2)
EraseBlocks: preserving reserved block (0x3)
EraseBlocks: preserving reserved block (0x4)
EraseBlocks: preserving reserved block (0x5)
EraseBlocks: found a bad block (0x61) - skipping...
EraseBlocks: found a bad block (0x1a6) - skipping...
EraseBlocks: found a bad block (0x48c) - skipping...
EraseBlocks: found a bad block (0x54d) - skipping...
EraseBlocks: found a bad block (0x644) - skipping...
Done.
WriteMBR: MBR block = 0x6.
Done.

IsValidMBR: MBR sector = 0x180 (valid MBR)
OpenPartition: Partition Exists=0x0 for part 0x21.
CreatePartition: Enter CreatePartition for 0x21.
LastLogSector: Last log sector is: 0x1fd3f.
CreatePartition: Start = 0x1, Num = 0x6b40.
Log2Phys: Logical 0x1 -> Physical 0x181
WriteMBR: MBR block = 0x6.
IsValidMBR: MBR sector = 0x180 (valid MBR)
OpenPartition: Partition Exists=0x0 for part 0xb.
CreatePartition: Enter CreatePartition for 0xb.
FindFreeSector: FreeSector is: 0x6b41 after processing part 0x21.
CreatePartition: Num sectors set to 0x19080 to allow for compaction blocks.
CreatePartition: Start = 0x6b80, Num = 0x19080.
WriteMBR: MBR block = 0x6.
BP_SetDataPointer at 0x0
WriteFlashNK : dwStoreOffset = 0x0
WriteData: Start = 0x0, Length = 0x358c6d0.
Log2Phys: Logical 0x1 -> Physical 0x181
WriteFlashNK : Kernel 0x0 0x358C6D0 0x80020000
ROMHDR at Address 80020044h
TOC {
dwSignature: 0x434F544E
BootCfg
{
ConfigFlags: 0x2020
dwBootDelay: 0x5
IP: 0.0.0.0
MAC Address: 00:00:00:00:00:00
Port: 0.0.0.0
SubnetMask: 255.255.255.0
}
ID[0]
{
dwVersion: 0x20005
dwSignature: 0x544F4245
String: eboot.bin
dwImageType: 0x1
dwTtlSectors: 0x100
dwLoadAddress: 0x87700000
dwJumpAddress: 0x87700000
dwStoreOffset: 0x1
}
ID[1]
{
dwVersion: 0x0
dwSignature: 0x0
String:
dwImageType: 0x0
dwTtlSectors: 0x0
dwLoadAddress: 0x0
dwJumpAddress: 0x0
dwStoreOffset: 0x0
}
ID[2]
{
dwVersion: 0x0
dwSignature: 0x0
String:
dwImageType: 0x0
dwTtlSectors: 0x0
dwLoadAddress: 0x0
dwJumpAddress: 0x0
dwStoreOffset: 0x0
}
ID[3]
{
dwVersion: 0x1
dwSignature: 0x48534643
String: NK
dwImageType: 0x8
dwTtlSectors: 0x6B19
dwLoadAddress: 0x80020000
dwJumpAddress: 0x80027F34
dwStoreOffset: 0x0
}
ID[4]
{
dwVersion: 0x0
dwSignature: 0x0
String:
dwImageType: 0x0
dwTtlSectors: 0x877499A4
dwLoadAddress: 0x0
dwJumpAddress: 0x0
dwStoreOffset: 0x87762790
}
A XIP region was written to the flash memory successfully.
INFO: OEMLaunch: Jumping to Physical Address 0x40027F34h (Virtual Address 0x80027F34h)...

Windows CE Kernel for ARM (Thumb Enabled) Built on Nov 3 2010 at 07:30:04
OAL Log enable : 0
OAL Log mask : 103

System Clock Info
[OAL] APLL_CLK : 800000000 Hz
[OAL] MPLL_CLK : 667000000 Hz
[OAL] EPLL_CLK : 96000000 Hz
[OAL] VPLL_CLK : 54000000 Hz

[OAL] ARM_CLK : 800000000 Hz
[OAL] HCLK_MSYS : 200000000 Hz
[OAL] PCLK_MSYS : 100000000 Hz
[OAL] HCLK_DSYS : 166750000 Hz
[OAL] PCLK_DSYS : 83375000 Hz
[OAL] HCLK_PSYS : 133400000 Hz
[OAL] PCLK_PSYS : 66700000 Hz
System Clock Info

OEM:-------------------------------------------
OEM: Normal Boot!!
OEM:-------------------------------------------
DCache: 128 sets, 4 ways, 64 line size, 32768 size
ICache: 128 sets, 4 ways, 64 line size, 32768 size
+OALInterruptInit
-OALInterruptInit(rc = 1)
DMSG: DrvWAITInitialize
-OALIoCtlHalGetHWEntropy(rc = 0)
DMSG: DrvWAITInitialize
[I2C:I] I2C Channel 0 is open
[I2C:I] I2C Channel 1 is open
[I2C:I] I2C Channel 2 is open
[I2C:I] I2C Channel 3 is open
[CMM_Init] VirAddrDram_0 : 0xad480000 VirAddrDram_1 : 0xa5f00000
############################### EHCI INIT ########################
[EHCI] InitailizeEHCI
[EHCI:INF] ++InitializeEHCI(): IRQ 144 sysintr 22 for EHCI