candence仿真问题

以前电路能够仿真，但今天仿真时“滴”的响一声没有出现波形。不知为什么。如下：
Command line:
/home/eda/mmsim61/tools.lnx86/spectre/bin/32bit/spectre input.scs\
+escchars +log ../psf/spectre.out +inter=mpsc\
+mpssession=spectre1_3579_3 -format sst2 -raw ../psf +lqtimeout\
900 -maxw 5 -maxn 5
spectre pid = 5607
Loading /home/eda/mmsim61/tools.lnx86/cmi/lib/4.0/libinfineon_sh.so ...
Loading /home/eda/mmsim61/tools.lnx86/cmi/lib/4.0/libnortel_sh.so ...
Loading /home/eda/mmsim61/tools.lnx86/cmi/lib/4.0/libphilips_sh.so ...
Loading /home/eda/mmsim61/tools.lnx86/cmi/lib/4.0/libsparam_sh.so ...
Loading /home/eda/mmsim61/tools.lnx86/cmi/lib/4.0/libstmodels_sh.so ...
spectre (ver. 6.1.0.151 -- 26 May 2006).
Includes RSA BSAFE(R) Cryptographic or Security Protocol Software from RSA Security, Inc.
Simulating `input.scs' on localhost.localdomain at 1:13:55 AM, Thur Jun 2, 2011.
Using new Spectre Parser.
Circuit inventory:
nodes 9
equations 12
bsim3v3 10
resistor 2
vsource 3
Entering remote command mode using MPSC service (spectre, ipi, v0.0, spectre1_3579_3, ).
********************************************
AC Analysis `ac': freq = (100 uHz -> 100 Hz)
********************************************
ac: freq = 173.8 uHz(4 %), step = 41.95 uHz(2 %)
ac: freq = 302 uHz(8 %), step = 72.91 uHz(2 %)
ac: freq = 691.8 uHz(14 %), step = 167 uHz(2 %)
ac: freq = 1.202 mHz(18 %), step = 290.3 uHz(2 %)
ac: freq = 2.754 mHz(24 %), step = 664.9 uHz(2 %)
ac: freq = 4.786 mHz(28 %), step = 1.156 mHz(2 %)
ac: freq = 10.96 mHz(34 %), step = 2.647 mHz(2 %)
ac: freq = 19.05 mHz(38 %), step = 4.6 mHz(2 %)
ac: freq = 43.65 mHz(44 %), step = 10.54 mHz(2 %)
ac: freq = 75.86 mHz(48 %), step = 18.31 mHz(2 %)
ac: freq = 173.8 mHz(54 %), step = 41.95 mHz(2 %)
ac: freq = 302 mHz(58 %), step = 72.91 mHz(2 %)
ac: freq = 691.8 mHz(64 %), step = 167 mHz(2 %)
ac: freq = 1.202 Hz(68 %), step = 290.3 mHz(2 %)
ac: freq = 2.754 Hz(74 %), step = 664.9 mHz(2 %)
ac: freq = 4.786 Hz(78 %), step = 1.156 Hz(2 %)
ac: freq = 10.96 Hz(84 %), step = 2.647 Hz(2 %)
ac: freq = 19.05 Hz(88 %), step = 4.6 Hz(2 %)
ac: freq = 43.65 Hz(94 %), step = 10.54 Hz(2 %)
ac: freq = 75.86 Hz(98 %), step = 18.31 Hz(2 %)
Accumulated DC solution time = 20 ms.
Intrinsic ac analysis time = 10 ms.
Total time required for ac analysis `ac' was 30 ms.
modelParameter: writing model parameter values to rawfile.
element: writing instance parameter values to rawfile.
outputParameter: writing output parameter values to rawfile.
designParamVals: writing netlist parameters to rawfile.
primitives: writing primitives to rawfile.

你的output里面是怎么写的

奥。对了，是output问题。谢谢了。