cc2640standby模式怎么正确进入

我关了广播和定时器还是有几个uA的跳变电流

您可以参考TI的例程，如SimpleBLEPeripheral。若是没有任何任务需要处理发生，TI-RTOS会把设备置于待机状态。当设备需要广播时，它会自动唤醒

您可以参考appBLE.cfg。当CPU处于IDLE状态时，会使用standbyPolicy。 

/* Idle CPU when threads blocked waiting for an interrupt */
Power.idle = true; 
Power.policyFunc = Power.standbyPolicy;

Hi

这是一个简单的demo，在实际使用在建议您用信号量来操作。

如果是使用semphare_pend将当前任务挂起使系统进入standby的，则当其他地方（比如中断处理中）post了这个信号量，系统会退出standby，当前task继续执行semphare_pend之后的语句。在standby是无法执行任何程序的。

/*
 * Copyright (c) 2016-2017, Texas Instruments Incorporated
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * *  Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *
 * *  Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * *  Neither the name of Texas Instruments Incorporated nor the names of
 *    its contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
 * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
 * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
 * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

/*
 *  ======== pinStandby.c ========
 */
#include <unistd.h>

/* Driver Header files */
#include <ti/drivers/PIN.h>
#include <ti/drivers/pin/PINCC26XX.h>

/* Example/Board Header files */
#include "Board.h"

/* Led pin table */
PIN_Config LedPinTable[] =
{
    Board_PIN_LED0    | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX, /* LED initially off */
    Board_PIN_LED1    | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX, /* LED initially off */
    PIN_TERMINATE                                                                      /* Terminate list */
};

/*
 *  ======== mainThread ========
 */
void *mainThread(void *arg0)
{
    PIN_State   pinState;
    PIN_Handle  hPin;
    uint_t      currentOutputVal;
    uint32_t    standbyDuration = 5;

    /* Shut down external flash on LaunchPads. It is powered on by default
     * but can be shut down through SPI
     */
    #ifdef Board_shutDownExtFlash
        Board_shutDownExtFlash();
    #endif

    /* Allocate LED pins */
    hPin = PIN_open(&pinState, LedPinTable);

    /*
     * Repeatedly sleeps for a duration, to allow repeated entry/exit
     * from standby. The LED states are toggled on each iteration
     */
    while(1) {
        /* Sleep, to let the power policy transition the device to standby */
        sleep(standbyDuration);

        /* Read current output value for all pins */
        currentOutputVal =  PIN_getPortOutputValue(hPin);

        /* Toggle the LEDs, configuring all LEDs at once */
        PIN_setPortOutputValue(hPin, ~currentOutputVal);
    }
}

我用例程进低功耗和我加了传感器程序进低功耗都有这个毛病，我按照手册近低功耗的办法，关闭射频广播和所有定时任务定时器，再进入低功耗的时候还是有几个uA的跳变电流，周期在几秒钟内从0.1uA跳到8uA左右。是否与io口漏电流有关如果是该怎么操作

你抓一下电流波形和VDDR电压对照一下，可能是给VDDR充电，参考SWRA478A文档5.3.2章节

如果是持续的话，应该是其他地方在耗电

你这个文档我找不到能发给我吗

现在更新到C版本了，到如下链接

http://www.ti.com/lit/an/swra478c/swra478c.pdf

下载

主要是电流周期性变化的会跟什么有关