请教drill_size编辑问题。

drill_size在装了9.2B后补偿出来的带小数。改了drill_size.tab后仍然不行。
就去拷贝了个其他人编辑的drill_size，结果补偿是整数了，但超过6.2的孔却不会补偿（drill_size.tab都是一样的）这样容易出错。
请大虾们帮我看看我的drill_size究竟小数是那里的参数没弄好，谢谢！
#！/bin/csh
# File Name:    drill_size
#  $1  - board thickness (as defined in the D.T.M. window)
#  $2  - finished hole size
#  $3  - hole type (VIA,PLATE,NPLATE)
#  $4  - min_tol
#  $5  - max_tol
#  $6  - user parameter string
#  $7  - output file pathname (which the system reads the results from)
#  $8  - tool number
#  $9  - drill bit designator
# Set numeric variables to have text names.
set BD_THK = `echo "$1"`
set FIN_SZ = `echo "$2"`
set H_TYPE = `echo "$3"`
set MN_TOL = `echo "$4"`
set MX_TOL = `echo "$5"`
set USER_P = `echo "$6"`
set OUTPUT = `echo "$7"`
set TL_NUM = `echo "$8"`
set DRL_DS = `echo "$9"`
# Set the basic enlargement factor based on the user parameter selected.
if ($USER_P == "hal") then
   set ENLARGE = 6
else if ($USER_P == "au") then
   set ENLARGE = 4
else if ($USER_P == "hr") then
   set MX_TOL = 4
   set ENLARGE = 6
endif
# Nominal size for non-plated holes (finish size plus ENLARGE value).
if ($H_TYPE == "NPLATE") then
   set SIZE = `echo "scale = 1 ; $FIN_SZ + 2 + ( $MX_TOL - $MN_TOL ) / 2 " | bc -l`
else if ($H_TYPE == "VIA") then
   set SIZE = `echo "scale = 1 ; $FIN_SZ + 0 + ( $MX_TOL - $MN_TOL ) / 2 " | bc -l`
else
   set SIZE = `echo "scale = 1 ; $FIN_SZ + $ENLARGE + ( $MX_TOL - $MN_TOL ) / 2 " | bc -l`
endif
# Split the final size number into two parts: 1 - integral part 2 - decimal part
set SIZE = `echo "scale = 2 ; ($SIZE * 25.4) / 100" | bc -l`
set Decimal_Size = `echo $SIZE | awk95 -F '.' '{print $2}'`
set Integral_Size = `echo $SIZE | awk95 -F '.' '{print $1}'`
# Choose the DRL_SIZE by the $SIZE, here are 4 values to decide which is the final drill size
if ($Decimal_Size == 00 || $Decimal_Size == 50) goto final_cal
if ($Decimal_Size == 25 || $Decimal_Size == 75) goto semi_cal
if ($Decimal_Size > 50) then
   if ($Decimal_Size >= 75) then
      set Integral_Size = `echo "scale = 2 ; $Integral_Size + 1" | bc -l`
      set Decimal_Size = 0
   else
      set Decimal_Size = 50
   endif
else
   if ($Decimal_Size >= 25) then
      set Decimal_Size = 50
   else
      set Decimal_Size = 0
   endif
endif
goto final_cal
semi_cal:
if ($Decimal_Size == 25) then
   set Decimal_Size = 50
else
   set Decimal_Size = 0
   set Integral_Size = `echo "scale = 2 ; $Integral_Size + 1" | bc -l`
endif
final_cal:
# Change the number into high resolution number to match micron
set SIZE = `echo "scale = 3 ; $Integral_Size + ($Decimal_Size / 100)" | bc -l`
set HR_SIZE = `echo "scale = 4 ; (($SIZE * 100) / 25.4)" | bc -l`
set I_HR_SIZE = `echo $HR_SIZE | awk95 -F '.' '{print $1}'`
set D_HR_SIZE = `echo $HR_SIZE | awk95 -F '.' '{print $2}'`
set ACU_D_HR_SIZE = `echo "scale = 3 ; $D_HR_SIZE / 10.0" | bc -l`
set D_ACU_D_HR_SIZE = `echo $ACU_D_HR_SIZE | awk95 -F '.' '{print $2}'`
set I_ACU_D_HR_SIZE = `echo $ACU_D_HR_SIZE | awk95 -F '.' '{print $1}'`
#if ($D_ACU_D_HR_SIZE >= 500) then
#   set I_ACU_D_HR_SIZE = `echo "scale = 3 ; $I_ACU_D_HR_SIZE + 1" | bc -l`
#   set D_ACU_D_HR_SIZE = 0
#else
#   set D_ACU_D_HR_SIZE = 0
#endif
set ACU_D_HR_SIZE = $I_ACU_D_HR_SIZE
set D_HR_SIZE = $ACU_D_HR_SIZE
set HR_SIZE = `echo "scale = 3 ; $I_HR_SIZE + ($D_HR_SIZE / 1000)" | bc -l`
set DRL_SIZE = $HR_SIZE
set DRL_DES = ` echo "scale=2; $SIZE / 10 " | bc `
# Output the result
echo "$DRL_SIZE $DRL_DES"

那么大孔一般情况下都是锣出来的！

我知道啊，但有些是PTH，要扩孔出来的

如果钻孔没补偿，在genesis里面做扩孔的话就会弄错。

这个东西 貌似是一个脚本吧  
   我们公司都是用原始的CAM350打带的  
genesis输出来的资料  钻机和锣机识别不了 呵呵

扩孔在genesis里面有另外一种做法，就是用槽的方式钻出来

是的，这是个脚本，现在就是不知道那个位置的计算方式不对，导致钻孔有小数。
一般改了drill_size.tab的精度就可以了，但这个drill_size在计算方面肯定有个位置精度不对
要修改它的原因是，可以不受孔径大小的补偿控制。其他的6.2以上就不补偿了。
这个文件写的格式跟原始的也不同，没法参考修改，主要是不懂代码

ddddddddddddddddddddddddddd

6.2的孔不会补偿是因为drill_size.tab刀库最大钻刀为6.2，你可以添加刀库来达到你得目的！可以制作监控成品尺寸大于多少报警提示！这样出错几率就大大降低了！

学习了，谢谢啊

  一般6.0以上的孔，如果是NPTH孔的话都会做成锣的，是PTH孔的话会做成扩孔，手动加大，用GENESIS做孔的话在Auto Drill Manager 中设置

Auto Drill Manager 是在那里进入的?