9.2c版本阴阳后无法导出钻带文件,求解!
时间:10-02
整理:3721RD
点击:
9.2c版本阴阳排版后无法导出钻带文件提示
我在这个目录下面加了个machine文件后就可以导出去了,我不赶保证钻带是否正常。
然而这个版本的这个目录下面和其它版本多了个
文件。如果我把这个文件的名称改成machine也可以导出去。
这个文件的内内如下
rout_layer = ncd
hook_units = mm
no_touch_cpr = no
tent_ar = 12
reg {
xsize1 = 40.0
xsize2 = 0
ysize = 30.0
xover = 0
angle = 0
mirror = no
xoff = 0.0
yoff = 0.0
xorigin= .0
yorigin= .0
dx1 = 1
dy1 = 2
xscale = 1
yscale = 1
xscale_o = 0
yscale_o = 0
}
format {
format = esi laser
zeroes = trailing
units = mm
tool_units = mm
nf1 = 2
nf2 = 4
modal_coords = yes
}
optimize {
optimize = yes
break_sr = no
xspeed = 100
yspeed = 100
reduction_percent = .01
iterations = 20
}
rout_layer = nc_rout
hook_units = mm
no_touch_cpr = yes
tent_ar = 1000
nibble {
custom = no
val {
min_size = 0
max_size = 999
num_holes = 64
}
}
slot {
custom = yes
overlap = 8.0
total_overlap = 10.0
}
panel {
xsize = 19
ysize = 25
reg {
fit = yes
angle = 0
mirror = no
xoff = -0.5
yoff = -0.5
version = 0
}
start_end {
split {
start = no
end = yes
min_dist = 50
x1 = 18.125
y1 = 6.625
x2 = 18.375
y2 = 12.0
}
}
}
tools_assign {
mode = increasing_size
}
out_hook {
exists = no
header = no
eof = no
tool_change = no
tool_finish = no
}
哪位大哥看下怎么样解决这个不能导出钻带的问题。
我在这个目录下面加了个machine文件后就可以导出去了,我不赶保证钻带是否正常。
然而这个版本的这个目录下面和其它版本多了个
文件。如果我把这个文件的名称改成machine也可以导出去。
这个文件的内内如下
rout_layer = ncd
hook_units = mm
no_touch_cpr = no
tent_ar = 12
reg {
xsize1 = 40.0
xsize2 = 0
ysize = 30.0
xover = 0
angle = 0
mirror = no
xoff = 0.0
yoff = 0.0
xorigin= .0
yorigin= .0
dx1 = 1
dy1 = 2
xscale = 1
yscale = 1
xscale_o = 0
yscale_o = 0
}
format {
format = esi laser
zeroes = trailing
units = mm
tool_units = mm
nf1 = 2
nf2 = 4
modal_coords = yes
}
optimize {
optimize = yes
break_sr = no
xspeed = 100
yspeed = 100
reduction_percent = .01
iterations = 20
}
rout_layer = nc_rout
hook_units = mm
no_touch_cpr = yes
tent_ar = 1000
nibble {
custom = no
val {
min_size = 0
max_size = 999
num_holes = 64
}
}
slot {
custom = yes
overlap = 8.0
total_overlap = 10.0
}
panel {
xsize = 19
ysize = 25
reg {
fit = yes
angle = 0
mirror = no
xoff = -0.5
yoff = -0.5
version = 0
}
start_end {
split {
start = no
end = yes
min_dist = 50
x1 = 18.125
y1 = 6.625
x2 = 18.375
y2 = 12.0
}
}
}
tools_assign {
mode = increasing_size
}
out_hook {
exists = no
header = no
eof = no
tool_change = no
tool_finish = no
}
哪位大哥看下怎么样解决这个不能导出钻带的问题。
怎么没有人回复啊
直接更新下你的阴阳排版就可以导出去了,还改什么文件啊
怎么更新呢,大哥能否说祥细些.
要配套的machine文件啊,原则上不能随便改一个文件为machine
没有的话,只能根据结果来修正了
学习学习~~~~